Slow strain rate technique for studying hydrogen induced cracking in 34CrMo4 high strength steel

Alloy hardened steels offer excellent combination of mechanical properties, hardenability and corrosion resistance. 34CrMo4 is a medium carbon, low alloy steel widely used due to a good combination of high-strength, toughness and wear resistance. However, this steel experiences hydrogen embrittlement (HE), a complex phenomenon depending on the composition and microstructure. This work estimates de loss of the mechanical properties caused by hydrogen in electrochemically H-charged specimens in absence of mechanical stress but also, at low strain rate and constant load. H-charging for 2 and 6 h induce YS losses of about 40% and 71% and UTS losses of 39% and 59%, respectively. The synergistic effect of the stress and the H-charging process leads to a higher loss, 91%, and a faster brittle fracture even though hydrogen content is similar to those firstly H-charged and then tested in air.     

汽车锁零部件碱性锌镍合金电镀工艺

介绍了汽车锁零部件碱性挂镀锌镍合金电镀生产线的开发过程,包括前期市场调研、中期小槽试验、后期成本核算、电镀工艺流程确定、废水处理工艺制定以及阳极膜应用可行性分析。     

冲击载荷下TC18钛合金力学性能模拟研究

TC18钛合金在退火状态下的屈服强度非常高,进行动态力学性能测试存在一定困难,可优先考虑采用数值模拟方法对其动态力学性能进行研究,而数值模拟结果的精确性主要取决于合金本构方程的精确性。为了减少数值模拟与实验结果之间的差异,在Johnson-Cook模型的基础上做了调整,利用ABAQUS软件的子程序接口自定义了材料本构子程序UMAT,以代码的形式来扩展ABAQUS程序的功能。通过与ABAQUS/Standard软件分析结果以及实验结果的对比,验证了自定义材料本构子程序UMAT计算结果的精确性与可靠性。该研究可为TC18钛合金的结构设计提供参考。     

超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

针对100 mm超厚板TC4钛合金电子束焊接接头，采用慢应变速率拉伸方法评价接头在人造海水中的应力腐蚀敏感性，分析接头的显微组织和断口形貌，对接头的腐蚀机制进行研究. 结果表明，室温条件下应变速率为ε=1×10-6 s-1时，母材在海水中未表现出应力腐蚀敏感性；焊缝上部、中部和下部具有轻微应力腐蚀敏感性. 焊缝在海水中发生阳极溶解，产生氢吸附，导致裂纹的萌生. 同时氢扩散诱导α'相界及α'相内发生位错塞积，进而使裂纹在更低的应力水平下发生扩展.     

Probing the degenerate pattern growth of {100}<011> orientation in a directionally solidified Al-4.5 wt% Cu alloy

Degenerate pattern is a seemingly disordered morphology but it exhibits the inherently ordered crystal connected with tip-splitting and limited stability which makes it difficult to observe in the metallic system. Here we employ (100)[011] orientated planar-front seeds using directional solidification and reveal the fundamental origins of the degenerate pattern growth in an Al-4.5 wt% Cu alloy. We find that the spacing of the tip-splitting (λ) in the degenerate of the alloys followed a power law, λ∝V^−0.5, and the frequency (f) of the splitting was related to the growth velocity (V) by ƒ∝V^1.5. The dimensionless growth direction (θ/θ₀) increased monotonously and approached 0.6 with faster velocity, attributed to its anisotropy in the interface kinetics. Once growth velocity exceeded a threshold, two types of pattern transitions from degenerate to regular dendrites were proposed. One of them exhibited a random and chaotic mode and the other underwent a rotation in growth direction.     

Corrosion behaviour of Al1.3CrFeNi chemically complex alloy

In this study, corrosion behaviour of double-phase Al_1.3CrFeNi chemically complex alloy was investigated, including hot corrosion and electrochemical corrosion. Hot corrosion behaviour of Al_1.3CrFeNi alloy was explored in molten 75 wt-% Na₂SO₄?+?25 wt-% NaCl salt. The result revealed that the corrosion kinetic curve of Al_1.3CrFeNi alloy followed the exponential rate rule through mass loss measurement. In addition, it prevented that the formed corrosion layer had obvious stratification including external granular Al₂O₃ and inner porous Cr₂O₃ when corrosion time was up to 100?h. Besides, it should be noted that the Al_1.3CrFeNi alloy was sensitive to the molten salt containing chlorine, which makes the alloy surface leave voids and bring about acceleration of corrosion. Meanwhile, electrochemical corrosion resistance of Al_1.3CrFeNi alloy in NaCl solution with different concentrations (0.6, 1.0 and 2.0?mol?L^?1) was investigated at room temperature. The results revealed that Al_1.3CrFeNi alloy showed superior corrosion resistance in NaCl solution due to the existence of Al and Cr which aid the formation of protective oxide layer.     

邻菲罗啉光度法测定钒铝合金中铁

应用邻菲罗啉光度法测定钒铝合金试样中铁时,存在试样溶解难且试样中高含量钒会干扰铁的测定的问题。实验采用硝酸、盐酸溶解试样,硫酸冒烟赶尽氮氧化物,加入盐酸羟胺将钒(V)还原为钒(IV),在沸水浴条件下加入乙酸-乙酸铵缓冲溶液消除钒(IV)的干扰,从而实现了钒含量高的钒铝合金中铁的测定。实验表明,显色液中铁的质量浓度在0~1.2μg/mL符合郎伯比尔定律,校准曲线的线性相关系数R²=0.9998;测定下限为0.005%(质量分数)。方法用于钒铝合金中铁含量的测定,测定结果相对标准偏差RSD(n=8)小于3%,回收率在98%~103%之间。按照本法和DB51/T 2038—2015《钒铝合金 硅、铁等15种杂质元素含量的测定 电感耦合等离子体原子发射光谱法》分别测定4个钒铝合金样品中铁,两种方法测定结果相一致。     

镍基高温合金液相扩散焊接头组织及性能

镍基高温合金GH4413在高温下具有较为优异的高温持久强度和抗蠕变性能，在航空发动机和各种工业燃气轮机中得到广泛应用。以BNi 2作为填充合金材料使用液相扩散焊对GH4413合金进行了连接，研究了在焊接温度分别为1 030和1 080 ℃、保温时间分别为30和60 min等不同焊接参数下GH4413镍基高温合金的接头微观组织、成分分布和显微硬度。扫描电镜(SEM)以及能谱分析结果表明，当焊接温度为1 080 ℃、保温时间为60 min 时，钎缝组织中形成了性能良好的固溶体，且随着焊接温度的升高和保温时间的延长，钎缝的宽度增加，钎料元素向母材中的扩散深度逐渐增加，在母材近缝区形成了金属间化合物。     

钛/铝异种金属冷金属过渡增材制造

采用TC4和ER2319焊丝直流/变极性冷金属过渡实现异种金属电弧增材制造，通过金相显微镜、扫描电镜、透射电镜、能谱、硬度试验、纳米压痕以及拉伸试验等方法对钛/铝构件界面组织特征与力学性能进行分析.结果表明，在钛合金表面堆积铝合金时，只有少量的钛合金熔化，钛原子扩散到液态铝合金中，形成不同长度的TiAl₃金属间化合物.10 μm左右的反应层在钛/铝界面形成.邻近钛侧的反应层均匀连续，靠近铝合金一侧的反应层呈现长条状或块状.界面反应层的显微硬度介于钛合金和铝合金显微硬度之间.构件的最高抗拉强度为111 MPa.